Use and maintenance of edging machine

The correct and reasonable use of the edging machine can not only ensure the normal production, but also prolong the life of the machine. Here is an introduction to the correct use of edging machine should pay attention to matters.

1, for a variety of newly purchased edging machine, be sure to read the instruction manual before use. After understanding the transmission principle of the machine, the role of various handles, handwheels, electrical buttons, waterways, and gas regulating valves, and mastering the maintenance knowledge of the machine, the machine can be operated.

2, the grinding head of the edge grinding machine has a greater impact on the grinding quality of glass, the position of the grinding head, moving clearance, etc. have been adjusted when leaving the factory, in addition to the use of the grinding head, the rest generally do not move, so as not to affect the grinding quality. In addition, the backward position of the grinding head is not easy to be too large, otherwise it is easy to damage the waterproof sleeve, causing water leakage, and easy to burn the motor.

3. Whether the cooling is sufficient also has a great impact on the grinding effect. Check the cooling line frequently for blockage. In particular, the pipeline of the linear edging machine is easy to be blocked by the bristles, and it is not easy to be detected after plugging, which will cause insufficient cooling and affect the quality of the edging.

4, the endless transmission used by the edging machine, the speed must be adjusted in the open state, otherwise it is easy to damage the stepless transmission of the edging machine.

5, the use of special-shaped machine precautions: ① The height of the special-shaped machine table suction cup is consistent on the grinding effect. When assembling, the manufacturer has self-grinding the five groups of suction cups, and selects the suction cups with the same thickness to keep the height of the suction cups consistent, so under normal circumstances, do not disassemble and assemble the suction cups. If the suction cup glue is damaged, it is necessary to choose the same thickness to replace. After using the vacuum pump for a period of time, due to water and other reasons, the vacuum degree will decrease (that is, the suction will decrease) phenomenon, so pay attention to check and troubleshoot, otherwise, the machine will work in the case of insufficient suction, on the one hand will affect the grinding quality, on the other hand, it is also prone to safety accidents.

6. Precautions for the use of linear edging machine: The working mode of linear edging machine (straight edge machine, round edge machine, bevel edge machine) is to grind the glass by clamping the front and back pressure plate and driving its linear movement. Two points must be paid attention to in use: ① The combination surface of the front and back pressure plate and the guide rail should be lubricated frequently, otherwise the normal service life of the machine will be affected by premature wear of the front and back pressure plate and the working surface of the guide rail. Although some models have automatic lubrication devices, it is necessary to regularly check whether the lubrication pipeline is smooth; When clamping the glass, the clamping force should be appropriate, too loose affects the grinding quality, too tight will increase the machine load, easy to produce shaking crawling phenomenon, and easy to crush the glass when grinding thin glass. The size of the clamping force can be tested by clamping a slightly larger glass on the machine, that is, the glass is clamped in the middle of the machine, the hands are forced to move the glass in the shutdown state, and the clamping force is adjusted to just when the hands can not move.

7, the use of the mold machine precautions: ① the mold of the touch machine has a great impact on the grinding accuracy. The working face of the template must be made with accurate shape and size and high finish. If the shape depends on the template, the transition must be smooth. When replacing the template and sucker, be sure to maintain the level of the working surface of the sucker, otherwise it will affect the grinding quality.

8, double-sided edging machine when using precautions: ① double-sided edging machine is a higher grade of edging machine, it is best to fix two to three people to operate, to ensure correct operation. When there is an error or failure in the procedure of the bilateral mill, it is best to ask the original manufacturer to send someone to repair and debug, and do not disassemble and repair under normal circumstances, so as to avoid confusing the procedure and causing production to stop.

　　Milling machine use and maintenance

　　Correct and rational use of the milling machine, not only to ensure normal production, but also play a role in extending machine life. Here about the proper use of milling machine should pay attention.

　　1, on purchase of new milling machine, using the former must first read the instruction manual. Find out the machine in the drive principle, a variety of handles, hand wheels, electric button, water, gas regulator valve, grasp the knowledge of machine maintenance, the only hands-on.

　　2, the milling machine grinding wheel head is good or bad quality of the glass have a greater impact, grinding head position, move the gap so the factory have been fine, except when using advance and retreat grinding head, the other not to move the general to affect the quality of grinding. In addition, the grinding head back position is not easy too large, otherwise easily damage the waterproof cover, resulting in leakage, and easy to burn out the motor.

　　3, the adequacy of the cooling effect of grinding also affected. Road to always check whether the cooling pipe clogging. Particular straight line edging machine bristles easily be blocked, and after blocking escape detection, would result in inadequate cooling of milling quality.

　　4, the milling machine using the CVT to regulate the speed must be in the issuing state, or milling machines easily damage the CVT.

　　5, special machines use Notes: ① sucker shaped machine table are the same level of greater impact on the grinding effect. Assembly of the five manufacturers have been self-sucker seat grinding, and pick the thickness of the plastic suction cups on the same high degree of consistency to enable the suction cup, so do not go under normal circumstances removable suction cups. If there is damage to the rubber suction cup, they have chosen to replace the same thickness. ② shaped machine vacuum pump in use for some time, due to other reasons, there will be water down the vacuum (ie, suction decreases) and, therefore, should pay attention to check and troubleshooting, otherwise insufficient suction machine to work, on the one hand will affect the mill cut quality, on the other hand are also prone to accidents.

　　6, when used straight-line edging machine Note: straight milling machine (straight edge machine, round edge machine, bevel edge machine) works through the glass before and after the clamp plate and drive the linear motion of the grinding. Must use two points: ① plate before and after the combination with the rail surface to be lubricated regularly, otherwise they will face in the front plate and the rails of the machine of premature wear and tear of normal life. Although some models automatic lubricating device, but we must always check the lubrication pipe is smooth; ② clamping force clamping the glass size should be appropriate, too loose quality of grinding, the machine load will increase too tight, easy to produce jitter creeping phenomenon, easy to wear thin glass Shihai folder broken glass. Clamping force can be a slightly larger size of glass caught in the machine for testing, namely: the machine will be caught in the middle of the glass, downtime state, his hands moving the glass plate, clamping force is transferred to the feeling just can not move his hands when appropriate.

　　7, when used by the molding machine Note: ① mode by touching on the grinding machine accuracy by the great impact. Face by the template shape and size must be done accurately and finish higher. If shaped by the template, be sure to smooth the transition at. ② change the template and the sucker, be sure to keep the level of suction face, otherwise it will affect the grinding quality.

　　8, bilateral milling machine when used Note: ① bilateral milling machine milling machine is a high grade, use of the best fixed two to three operations to ensure proper operation. ② grinding process of bilateral errors or failure, it is best you send the original manufacturer maintenance and debugging, in general, do not overhaul in order to avoid chaos caused by discontinued programs.